MOFLSTOMP 899 Posted September 12, 2012 Okay, so I'm attempting to overclock my i5-2500k. Stable at 4.2, 1.275 vcore, auto settings for everything else. I just can't get it to fully boot into windows once I put it past the 4.2 mark, even though there's plenty of room to OC. My motherboard is the Gigabyte GA-Z68X-UD3H-B3 which has multiple tales of hitting 4.7-4.8GHz without a problem, so I just don't know what's holding me back. Any ideas? Quote Share this post Link to post Share on other sites
dormantlemon 219 Posted September 12, 2012 most basic question first. liquid or air cooled? Quote Share this post Link to post Share on other sites
ctark 1983 Posted September 12, 2012 Only thing I could think of would be upping the voltage.I am far from a god at OC'ing though, could only get my i7-975 to 4.1Ghz stable. Though tbh didn't try very hard...Let us know how you make out! Quote Share this post Link to post Share on other sites
MrCoolness 547 Posted September 12, 2012 you need to up the core voltage and make sure you're not already overheating with the 4.2 ghz clock. Try using coretemp to check your cpu temps when booted in windows. Quote Share this post Link to post Share on other sites
MOFLSTOMP 899 Posted September 12, 2012 I'm idling at like 35C with the Xigmatek Dark Knight II Nighthawk Edition (single 120mm in pull config) and maybe topping out in the 50s under unrealistic load Quote Share this post Link to post Share on other sites
BLiNDBoi 930 Posted September 12, 2012 I have a i7 920, I've OC'd mine to 4.2 GHz, wasn't 100% stable even with a crazy high voltage. Upping voltage, make sure you're memory speed isn't too fast for its own specs along with with the mother board. Quote Share this post Link to post Share on other sites
blob 1985 Posted September 12, 2012 I have 2500k at 4GHz with no voltage increase, so it may be something else. You can try it though, I don't feel like going higher. Quote Share this post Link to post Share on other sites
MOFLSTOMP 899 Posted September 12, 2012 Full Specs list for what it's worth (besides video card, which is irrelevant)MB: Gigabyte GA-Z68X-UD3H-B3RAM: 4x4GB Corsair VENGEANCE (Black DDR3-1600)CPU: Intel Core i5-2500KPSU: Rosewill LIGHTNING Series 1000WHSF: Xigmatek Dark Knight II Nighthawk Ed.I think it might have something to do with the memory as well, since that was the limiting factor when I had my Phenom II X4 955. Should I try downclocking it to 1333 and see if I can get the system to full boot into W7 instead of hanging at the login screen? Quote Share this post Link to post Share on other sites
DarkPredator 1193 Posted September 12, 2012 I did the same thing you're doing now with an e8400 a long time ago. The only thing I suceeded in doing was de-stabilizing the CPU through too much voltage and reducing it's overall lifespan :S^ Warning Quote Share this post Link to post Share on other sites
MOFLSTOMP 899 Posted September 13, 2012 (edited) I did the same thing you're doing now with an e8400 a long time ago. The only thing I suceeded in doing was de-stabilizing the CPU through too much voltage and reducing it's overall lifespan :S^ WarningI've never put it into the unsafe voltage range of 1.4+. Max I've given it was like 1.375 when I tried to really push it before. I had it stable 3.7GHz at like 1.15V for a while, but I also wanted to crack the 4.5GHz barrier with this chip Edited September 13, 2012 by Roflstomp.mp3 Quote Share this post Link to post Share on other sites
BLiNDBoi 930 Posted September 13, 2012 Well if you just having trouble getting it to post, the is either not enough juice or just a straight up bad setting. I don't know how the BIOS works on 2500k chips, what is the max multiplier can you do? Quote Share this post Link to post Share on other sites
MOFLSTOMP 899 Posted September 13, 2012 Everything boots perfectly fine, but it hangs when the Windows Login screen shows up, and then bluescreens without an error code. Quote Share this post Link to post Share on other sites
BLiNDBoi 930 Posted September 13, 2012 That's just as bad as a no post boot, not all motherboards are the same you might just not be able to do 4.5GHz. Quote Share this post Link to post Share on other sites
Toxygen 1885 Posted September 13, 2012 I'd say to go ahead and stop trying, otherwise you may cause too much damage and have to buy some new shit. You don't really need to overclock that much, anyways. Quote Share this post Link to post Share on other sites
fatb0y 1337 Posted October 2, 2012 Sometimes.... the CPUs just can't do it. I don't mean the 2500k model series can't... I mean your specific 2500k can't. Quote Share this post Link to post Share on other sites
MOFLSTOMP 899 Posted October 23, 2012 Beating a dead horse, but I've got this thing up to a stable 3.8GHz @ 1.025v. Can I push it further without upping the voltage? Quote Share this post Link to post Share on other sites
BLiNDBoi 930 Posted October 23, 2012 You can try but if it doesn't post then you know your answer. Quote Share this post Link to post Share on other sites